Rete di fornitori verificati
Cable accessories sourced from qualified manufacturers with full IEC documentation — the same supply chain used for BOMFLEX project deliveries.
Kit giunto cavo & Cable Termination Kit Supplier
Cold shrink, heat shrink, and straight-through cable joint kits for MV and LV power cable systems — IEC 60840 e CEI 60502 compatible, available as standalone supply or consolidated with cable orders through BOMFLEX.
MV & LV Compatible Cold Shrink & Heat Shrink CEI 60502 / 60840
Underground Cable Joints
Substation Terminations
Overhead Line Connections
Industrial Installations
Progetti di energia rinnovabile
MV and LV Cable Joint Kits — Cold Shrink, Heat Shrink and Straight-Through
Cold shrink, heat shrink, and straight-through joint kits across MV and LV voltage ranges. Compatible with XLPE and PVC insulated cables from major manufacturers.
Product entries for this category are being prepared. Send your specification for direct factory support.
Specifiche tecniche
| Product Type | Joint Type | Voltage Grade | Cable Insulation | Conductor Range (mm²) | Standard |
|---|---|---|---|---|---|
| MV Cold Shrink Joint Kit | Straight-through / Branch | 3.6/6kV – 26/35kV | XLPE / EPR | 25 – 630 | CEI 60502-4 |
| MV Heat Shrink Joint Kit | Straight-through / Branch | 3.6/6kV – 26/35kV | XLPE / EPR | 25 – 630 | CEI 60502-4 |
| MV Cold Shrink Termination Kit | Outdoor / Indoor | 3.6/6kV – 26/35kV | XLPE / EPR | 25 – 630 | CEI 60502-4 |
| MV Heat Shrink Termination Kit | Outdoor / Indoor | 3.6/6kV – 26/35kV | XLPE / EPR | 25 – 630 | CEI 60502-4 |
| LV Straight-through Joint Kit | Straight-through | Up to 1kV | XLPE / PVC | 16 – 240 | CEI 60502-1 |
| LV Heat Shrink Termination Kit | Outdoor / Indoor | Up to 1kV | XLPE / PVC | 16 – 240 | CEI 60502-1 |
Joint kits are available for single-core and three-core cable configurations. Specify voltage grade, cable insulation type, conductor cross-section, and number of cores when requesting a quote.
Cable Accessories and Cables — Supplied Together in One Shipment
Power infrastructure projects require cable joint kits, termination kits, and cable accessories to arrive on site at the same time as the cables — coordinating multiple suppliers for the same delivery schedule creates significant procurement risk.
LX Cable’s BOMFLEX service consolidates your complete project accessory and cable requirement:
For EPC contractors and utility procurement teams, BOMFLEX eliminates the coordination cost of sourcing cable accessories and cables from different suppliers.
- MV cable joint kits and termination kits matched to your cable specification
- MV and LV power cables across voltage grades and conductor cross-sections
- Surge arresters, insulators, and overhead line hardware
- Overhead conductors (ACSR / AAAC / AAC) and optical fiber cables
- Consolidated into a single factory-verified shipment with matched documentation
Why Project Teams Source Accessories from LX Cable
25+ Anni di esperienza
Supporting power infrastructure projects since the 1990s, with deep knowledge of accessory-to-cable compatibility across voltage grades and installation types.
Documentazione conforme a IEC
Joint kits and termination kits supplied with full test reports, installation instructions, and compliance certificates ready for project handover.
130+ Paesi consegnati
Proven cross-border logistics for accessories and cables — consolidated shipments to over 130 paesi in tutto il mondo.
Domande frequenti
Cold shrink joint kits use pre-expanded silicone rubber sleeves that contract around the cable when a core support is removed — no heat source is required, which makes them suitable for environments where open flame or heat guns are restricted, such as tunnels, oil platforms, or confined spaces. Heat shrink joint kits use thermoplastic sleeves applied with a heat gun; they are widely available and lower in cost but require controlled heating conditions during installation. Both types are available for MV XLPE cables from 3.6kV to 35kV.
Cable joint kits must be compatible with the cable’s insulation material (XLPE or EPR), conductor cross-section, grado di tensione, and number of cores. They are not cable-manufacturer-specific, but the installation parameters — such as insulation diameter and screen/shield type — must match the kit specification. When ordering joint kits alongside cables from LX Cable, compatibility is verified and documented as part of the BOMFLEX supply process.
MV cable joint and termination kits are available for voltage grades from 3.6/6kV up to 26/35kV, covering the most common medium voltage distribution ranges including 6kV, 10kV, 15kV, 20kV, and 33kV systems. Specify the system voltage and cable construction when requesting a quote.
SÌ. Attraverso il servizio BOMFLEX, LX Cable can supply MV or LV power cables together with matched cable joint kits, termination kits, surge arresters, and other accessories in a single consolidated shipment. This eliminates the need to place separate orders and coordinate delivery timing across suppliers.
Each kit is supplied with a product datasheet, installation instructions, and IEC test report. Upon request, compliance certificates (CE, RoHS) and material safety data sheets can be provided for project handover documentation.
Provide the following parameters: cable voltage grade (kV), cable insulation type (XLPE / EPR / PVC), conductor cross-section (mm²), number of cores (1C or 3C), and joint application (straight-through, branch, or termination — indoor or outdoor). Upload your cable datasheet or project specification sheet via the inquiry form and our technical team will confirm kit compatibility and availability.
